Author Topic: Wireless energy transfer - Idea  (Read 12847 times)

0 Members and 1 Guest are viewing this topic.

Marco2001

  • Mission Commander
  • *****
  • Posts: 353
Wireless energy transfer - Idea
« on: March 13, 2011, 12:08:30 PM »


Wireless energy transfer
( sending electric energy without using cables, that will power-up equipement outside the base, like: auger, comm-tower, portable light etc. )






For a long time I thought that wireless energy transfer is possible, but not very efficient.
There are many types of wireless energy transfer: magnetic, radio-wave, micro-wave and finally - laser.

Wireless energy transfer - http://en.wikipedia.org/wiki/Wireless_energy_transfer

In space exploration Laser energy transfer seems very tempting: with low air density of the moon and mars, the beem efficiency would be very high, energy converting mechanism would be very small and easy in maintance, they would transfer energy to specific locations many miles away instead of using an on-site generators (which would power-up the equipement [like: mining equipement] many miles away from the base) or instead of using tons of electric wires (which are also sensitive to radiation and solar flares). Laser wireless energy transfer also has the advantage of no radio-frequency interference to existing radio communication. Morover - you can transmit large data in the laser stream.

So why haven't the laser energy transfer not have been used yet?
Quote
   
1. Conversion to light, such as with a laser, is inefficient
2. Conversion back into electricity is inefficient, with photovoltaic cells achieving 40%-50% efficiency.[39] (Note that conversion efficiency is rather higher with monochromatic light than with insolation of solar panels).
3. Atmospheric absorption causes losses.
4. As with microwave beaming, this method requires a direct line of sight with the target.
http://en.wikipedia.org/wiki/Wireless_energy_transfer#Laser_method

So why am I mentioning this?
Becouse there hase been made a technological breakthrough in 2009.

Quote
At the 2009 Challenge, on November 6, 2009, LaserMotive successfully used lasers to drive a 4.8 kg (11 lb) device up a 900 m (2,950 ft) cable suspended from a helicopter.[4][5] Energy is transmitted to the climber using a high-power infrared beam.[6] LaserMotive's entry, which was the only to top the cable, reached an average speed of 13 km/h (8.1 mph) and earned a $900,000 prize. This marked both a performance record, and the first award of a cash prize at the Challenge.[5]

On October 28, 2010, Lasermotive set a flight endurance record at the Future of Flight Center by powering a quadcopter uav for more then 12 hours using laser. [7]
http://en.wikipedia.org/wiki/LaserMotive



LaserMotive - Who We Are, and What is Power Beaming - http://www.youtube.com/watch?v=-9ukRpvolYg

Academias Complicated Version of Wireless Power Transmission 1975 NASA JPL Goldstone Demonstration - http://www.youtube.com/watch?v=koqQ5K7AEEs

The Space Elevator Competition - 09.11.03 - http://www.youtube.com/watch?v=RaUEL4bZajo&feature=fvwrel

Poland here. My time: GMT + 1h
Writing a book about Mars. Any ideas? Type to me.
I'am an Astrobiology/Biology student.

profit004

  • MCCS Test
  • Mission Commander
  • ******
  • Posts: 418
Re: Wireless energy transfer - Idea
« Reply #1 on: March 13, 2011, 12:40:38 PM »
I had always thought they could do something like this, I am glad to see it was actually done.

I do not know gameplay wise anywhere this would fit in of course, but it would be a neat thing if it was incorporated.

On a side note.  The effect on a human with a 2000 watt laser beam would be instantaneous and brutal.  Safely capturing said beam at the other end would also be a challenge, even at 50% efficiency that is still a lot of heat the laser collector has to dissipate.  I imagine on mars almost everything this could be useful for, a RTG or RSG would be a better choice.


Marco2001

  • Mission Commander
  • *****
  • Posts: 353
Re: Wireless energy transfer - Idea
« Reply #2 on: March 13, 2011, 02:57:11 PM »
As I read - the beam is safe because, when something crosses it's path, it automaticly turns-off (it can count the reflexion intensity sudden drop and beam homecoming time).

As for the usage in the game - I see lot's of opportunities.
For instance - you have a LSSM located somewhere around the map, near rich ore-deposit. This single module is located far away from base, and needs lot's of power: for mining equipement, for sebatier/electroliser, for Life Support, pumps, player EVA charge.
You can send a half dozen generators there that run's on methane or half dozen RTG's or tens of solar panels to support that energy usage...that's a lot of Excess (and heavy) equipement that you will have to send to Mars from Earth.
On the other hand - a wireless laser power can transfer all the energy LSSM needs from the main base - where the thorium reactor is. No generators, no RTG's, no PVP - just a small laser-receiver on top of the LSSM that's the size of a single PVP pannel.
The laser can transmit data aswell....and can send power only when it's needed (LSSM can store the Excess power inside batteries).
Morover - on laser-energy-transmitter can send it's power to multiple sources. That means that multiple LSSM can be powered directly from the main base - just as if it was a power-net.

Quote
Marco: Hey Dubman - I'am at LSSM#1, and need some more power for my batteries (storm comming). Can you send me some more power?
Marcus: Sure thing. Seting output at 2500 Wats.
Marco: Thx :-)


Poland here. My time: GMT + 1h
Writing a book about Mars. Any ideas? Type to me.
I'am an Astrobiology/Biology student.

profit004

  • MCCS Test
  • Mission Commander
  • ******
  • Posts: 418
Re: Wireless energy transfer - Idea
« Reply #3 on: March 13, 2011, 03:04:19 PM »
The problem is the collector will be about as heavy as a small RSG in many cases.   The "Small" collector still needs a way to dissipate the heat from the conversion inefficiency and the heat sinks and the like will add to the weight significantly.  I suppose for 1-100 watt loads it would be ideal though as the collector would likely be able to dissipate that much heat safely with only a metal backing.  Under 20 watts if the beam was diffused a bit you could just use PV cells.

Utini

  • Specialist
  • ***
  • Posts: 23
Re: Wireless energy transfer - Idea
« Reply #4 on: March 13, 2011, 11:26:04 PM »
While a good idea, this runs into efficiency issues very quickly.  The climber was able to use the laser energy as it was a rather small robot which would have suffered a rather sizeable mass fraction for the batteries used for motive power.  The motors for the climber could be relatively small, as they didn't need to provide a lot of motive force for the climber to defeat gravity.  A remote mining / smelting facility, on the other hand, would require massive amounts of energy, on the order of tens or hundreds of kilowatts if smelting is occuring.  Even with best case photovoltaic conversion from the laser, you're getting equivalent thermal energy that has to be dumped.  This is obviously far more than can be passively managed.  Thus, an active cooling system has to be transported and set up, providing another failure point.  This system will require at least 50, probably in excess of 100 litres of cooling fluid to transfer the excess heat from the laser receiver to the radiator farm, which also has to be transported and set up.  A generator or RTG farm to provide the equivalent power would be as light or lighter and would provide fewer points of failure.

Having said that, a laser power system to recharge mini-blimps or gliders that could provide atmospheric and/or imaging data for the colony is feasible, due to similar reasons as the climber.

profit004

  • MCCS Test
  • Mission Commander
  • ******
  • Posts: 418
Re: Wireless energy transfer - Idea
« Reply #5 on: March 14, 2011, 12:25:19 AM »
I would like to point out the reason heat is such a major issue with this, is not due to the amount of heat, it is due to the concentration of heat.  Even with atmospheric blooming lasers will be focused on a very small area, and the material that is collecting the light also is very prone to not dissipating heat.

While in an RSG situation you can use passive diffusion over a much larger area using only metal heat sinks, you can get away with a much simpler lighter cooling solution even though the low efficiency of conversion means there is actually more heat to dissipate.

In the cases of a laser collection target, you are very nearly running up against the limits of physics to cool them.  On a side note though I am certain you could run a Stirling generator off the waste heat of anything over 100 watts in order to get even more power from this, but it would probably just power the thermal management loop.

A comparable alternative would be a a maser, as energy that is not collected theoretically *could* simply pass on through without generating significant heat.
« Last Edit: March 14, 2011, 12:39:41 AM by profit004 »

thedubman

  • Mission Commander
  • *****
  • Posts: 416
Re: Wireless energy transfer - Idea
« Reply #6 on: March 14, 2011, 05:45:27 PM »
Thats real nice, so not only do you get power converted from a laser on a PVA (see earlier question) its actually possible to shift lots of power quite effiently.

In a gaming sense, how does a geo-stationary nuclear powered sattellite which produces a laser transimitted to the surface to a collector (Ok atmospheric focusing problems can be resolved, yes I know power output would be an awful amount to produce a beam to reach the surface).. but in a gaming sense it could be a interesting way of solving a power issue..

Anyways, giving astronauts portable (or not) lasers to power equipment sounds like to much of a temptation to start firing at rivial factions... before you know it there will be Mars wars.

Marco2001

  • Mission Commander
  • *****
  • Posts: 353
Re: Wireless energy transfer - Idea
« Reply #7 on: March 16, 2011, 02:35:34 AM »
I just came back from hospital (a new type of flu virus in Poland, that I wasn't resistant off, and it got me paralysed so badly that I almost sufficated).
I see lot's of posts came-up. I don't know where do you peeple get those numbers from...please use links and quotes, becouse I spend lot's of time confirming what you have said and finding-out that many things are wrong.

Like:
Quote
The effect on a human with a 2000 watt laser beam would be instantaneous and brutal.  Safely capturing said beam at the other end would also be a challenge, even at 50% efficiency that is still a lot of heat the laser collector has to dissipate. 

Quote
LaserMotive developed the diode-laser beam system that kept the Pelican aloft. Near-infrared light from the equivalent of 250,000 laser pointers were focused and sent up to shine onto the quadrocopter's photovoltaic array, using a system of lenses and mirrors in the back of a delivery truck. The laser system served as a "wireless extension cord" for the Pelican, Nugent said. But the copter also had a battery capable of keeping the rotors running for a few minutes, just in case something went wrong with the 2.5-kilowatt laser.

Jordin Kare, another one of LaserMotive's co-founders and a pioneer in the field of laser propulsion, said the laser generated enough radiation to heat up your hand if you stuck it in the beam, but nowhere near enough to blast a hole in it. "We've actually cooked hot dogs with that laser, and it takes about four or five minutes," Kare told me. "Not exactly a death ray."
http://cosmiclog.msnbc.msn.com/_news/2010/10/28/5368938-copter-sets-a-laser-powered-record

Quote
As an aside, cooking a hot dog with a laser is not really much different than cooking it with an electric grill. The power level is comparable, the wavelength is a bit different (and so you want to wear protective goggles), and the toaster is just a bit more expensive, but otherwise there’s an on-off switch, a power dial, a bottle of Haynes, a bottle of Dijon, and squeeshy hot dog buns. There was no beer, even for guests.
http://www.spaceelevatorgames.org/category/team-specific/

--------------------------------------------------------------------

Quote
The problem is the collector will be about as heavy as a small RSG in many cases.


Stirling radioisotope generator (SRG)
Power:
Quote
Thus each SRG will utilise two Stirling converter units with about 500 watts
of thermal power supplied by two GPHS units and will deliver 100-120 watts of electric power.
http://en.wikipedia.org/wiki/Stirling_radioisotope_generator
Mass: 34 kg http://newfrontiers.larc.nasa.gov/PDF_FILES/09_NF_PPC_Schmidt.pdf

Advanced Stirling Radioisotope Generator (ASRG)
Quote
# Nominal power : 140 W
# Mass > 30 kg
http://en.wikipedia.org/wiki/Advanced_Stirling_Radioisotope_Generator

LaserMotive climbing device
Power:
Quote
With more than 1000 Watts transferred (peak) and roughly a horse power on average, their climber is clearly superbly designed, and is capable of achieving this speed.
http://www.spaceelevatorgames.org/
Mass (with batteries, motors and other parts):
Quote
At the 2009 Challenge, on November 6, 2009, LaserMotive successfully used lasers to drive a 4.8 kg (11 lb) device up a 900 m (2,950 ft) cable suspended from a helicopter.
http://en.wikipedia.org/wiki/LaserMotive

--------------------------------------------------------------------

Quote
The "Small" collector still needs a way to dissipate the heat from the conversion inefficiency and the heat sinks and the like will add to the weight significantly.

Quote
The next test is the Climber Melt Test.

If you recall, this is the test where the climber is illuminated at 100% power for the full climb duration (plus margin), and we confirm that it can take the heat.
We also look at the amount of power produced by the climber, to confirm that it is sufficient to move it up the cable at competitive speeds.

Quote
Moving to photovoltaics, NSS settled on a PV technology called TPV – Thermal Photovoltaics. These cells are optimized to operate with thermal IR radiation (longer wavelength than TRUMPF’s NIR 1030 nm beam) but have acceptable performance at this wavelength as well. More importantly, these cells can work with high light intensities, which means that you can get more power out of a smaller (and thus lighter) array, if only you can get the transfer the excess heat away from the cells.

What this calls for is a good heat exchanger – and this turned out to be the highlight of the day.

Check out the images of the climber. The TPV cells are completely immersed in acetone (4 ounces) which is vigorously boiling away under the heat load of the beam, completely evaporating every 15 seconds – only to be continuously captured by the bags and dripped back down onto the cells.

Acetone was chosen since it has the lowest boiling temperature, and so will be most effective as the working fluid.  This is a basically a cooling tower (or heat pipe) – something that was used by Centaurus Aerospace back in the 2005 games – using water in vacuum, in their case. The acetone solution is a lot lighter, and yes – more flammable.

We’ve looked into this issue, and we recognize that there are failure modes under which the system can develop a leak, but we feel that a) the acetone is far removed from any spark sources, b) there is only a small amount of acetone in the system, and c) there is no place for leaking acetone to accumulate, and so the consequences of an acetone leak are acceptable. We will also be monitoring the temperature of the PV receiver, and if we see it rising above the boiling point of acetone, we will know that the acetone is depleted and the climb is over.

So after observing the climber operating under full laser power, and with some modifications required, we’ve decided to ok the design, and allow NSS to catch up and participate in this year’s challenge.
http://www.spaceelevatorgames.org/

[4 ounces = 113 grams]
BTW: the same radiation techniqe is used in space.

Quote
On October 28, 2010, Lasermotive set a flight endurance record at the Future of Flight Center by powering a quadcopter UAV for more then 12 hours using laser propulsion.
http://en.wikipedia.org/wiki/LaserMotive
and
Quote
the Ascending Technologies Pelican quadrocopter and the LaserMotive power system were both capable of continuing indefinitely
http://lasermotive.com/news/blog/

--------------------------------------------------------------------

Quote
The climber was able to use the laser energy as it was a rather small robot which would have suffered a rather sizeable mass fraction for the batteries used for motive power.

Quote
In the test the team launched the Pelican using its five-minute-duration
battery and then turned on the laser power beam to provide continuous energy.
“It just sat there, 35 or 40 feet in the air, hovering constantly for
almost 12 and a half hours.”
The Pelican’s battery was recharged in flight, and near the end of
the test the craft flew over the spectators and landed under battery
power.
http://lasermotive.com/wp-content/uploads/2010/04/AUVSI-LaserMotiveUS0211.pdf

--------------------------------------------------------------------

Quote
The climber was able to use the laser energy as it was a rather small robot which would have suffered a rather sizeable mass fraction for the batteries used for motive power.  The motors for the climber could be relatively small, as they didn't need to provide a lot of motive force for the climber to defeat gravity. 
A remote mining / smelting facility, on the other hand, would require massive amounts of energy, on the order of tens or hundreds of kilowatts if smelting is occuring.
I reely don't understand what's your point here....Wat's are Wat's, no mather what uses them. If a robot gained 1000 Wats, than it can use 1000 Wats, no mather if it has batteries or low-/highpowered engines.
Why do you compare a mini-climbing robot with a big fabric on Earth? It's the energy source that we'r discussing.
If a mining-plant used a 10.000 kW of energy, you could deliver it in several ways:
1) send to Mars and plant in-situ a SECOND thorium reactor...
2) send to Mars and plant in-situ 100 square meters of PORTABLE PVP's. (efficiency 100 W/m^2 ---> http://solarwall.com/en/products/solarwall-pvt.php)
3) send to Mars and plant in-situ a 71 Advanced Stirling Radioisotope Generator (ASRG)
4) send lot's of methane-oxygen generators to Mars and produce and use in-situ tens-of-tons of oxygen and methane

and finally the BEST solution, becouse it's the most economical one:
5) send one thorium reactor in the main base. Use wireless-laser energy transfer to send excess energy it produces to locations that currently needs energy.
Those locations need only a few T/PV (thermal photo-voltanics) cells that receive power.
Those locations (like: mining facility) stores the excess power that they doesn't needs at the time. Unneded power is shut-down from the main base or stored inside regular lithium-batteries or high-cappacity batteries like Refualable Water Cells inside the mining facility thats stores unneded power. That power can then be used when you need more power, for the time when you do some super-energy-consuming processes. If the mining facility needs more power, the base sends more power inside the laser-beem. It's also required to understand that "not evertything will be done all-the-time"...that means that if you'r refining resources, you only refine them...when you have them. You electrolyse the water into H2 and O2...only when you have water. You create methane in Sebatier reactor...only when you need it for fueling rovers and/or generators, and you have water.
So in fact - you can send even smaller T/PV cells on Mars that will generate less power and the excess power will stack-up untill you use it.

BTW: That might be a nice gameplay scenario. For instance: You need to send enought power to the other side of the map, so that they could start a refining process, and send the refined resources back to the main base.

Two more things:
One - wireless energy transfer laser can send power to multiple sources.
Two - laser-energy can send a lot more than just few kilowats per-meter. For instance: http://www.popsci.com/technology/article/2010-04/skeeter-zapping-laser-entrepreneur-turns-sights-space-solar-power

Quote
This is obviously far more than can be passively managed.
Quote
Thus, an active cooling system has to be transported and set up [...]
Quote
This system will require at least 50, probably in excess of 100 litres of cooling fluid to transfer the excess heat from the laser receiver to the radiator farm
Quote
A generator or RTG farm to provide the equivalent power would be as light or lighter [...]
Quote
[...] and would provide fewer points of failure.

Do you reely have some proof of those fact or did you just made them-up?

--------------------------------------------------------------------

Quote
I would like to point out the reason heat is such a major issue with this, is not due to the amount of heat, it is due to the concentration of heat.  Even with atmospheric blooming lasers will be focused on a very small area, and the material that is collecting the light also is very prone to not dissipating heat.
Setting aside that I previously quoted that:
1) in the heat-exchenge test in 2009 those wireless-power laser-machines did good and passed the 100% beam light power.
2) in 2010 two machines flew over 12 hours constanlty only on the laser-beem power, and has proven to have the ability to fly indefinitely.
3) heat radiation can be managed by small amounts of simple fluids (and this techniqe is used also in space)
there are two more things that needs to be mentioned:
1) the laser doesn't needs to be fired from a single diode.
2) after 1 km, a sigle laser "dot" turns into a big circle.

Quote
On a side note though I am certain you could run a Stirling generator off the waste heat of anything over 100 watts in order to get even more power from this, but it would probably just power the thermal management loop.
Actually - no.
I know it sounds tempting, but the teams that DID try the stirling engine...lost.
It seems that a simple T/PV cell floating inside a cooling liquid is more efficient in terms of energy and mass than the laser-Stirling engine.

For instance:
Quote
One of the nice things about having multiple teams is that you get to see different ideas at work, and NSS is definitely not short on ideas.

Their first climber design featured a thermal (rather than photovoltaic) receiver, based on a Stirling engine. (Stirling engines are high efficiency engines often used for solar power generation) Stirling engines are a difficult proposition for a Space Elevator climber, since they typically weigh a lot more than a PV panel, and so NSS had to design and manufacture their own engine – and it is indeed a beauty. Using Helium as the working fluid, this engine also uses a transparent cylinder head in order to get the laser beam directly into a thermal absorber that is placed inside the cylinder – a perfect way to avoid the latency associated with the thermal mass of a regular absorber plate.

The problem NSS ran into was with properly sealing the engine while keeping the weight down. Anyone who’s ever worked with Helium knows how difficult it is to seal – it is a noble gas, and so is monatomic, which means its molecules are really small, and they get around most seals.

The other problem faced by thermodynamic engines is that while they are able to capture 100% of the energy of the beam (unlike the 30-50% of PV cells) they have to waste a good fraction of it at the heat exhaust side, and this gets worse the hotter the exhaust is. Which means that a thermodynamic engine needs to be coupled to an efficient heat exchanger – something that NSS started to design as well.

As it turned out, NSS was not able to solve the He sealing issue, and started working fast towards a photovoltaic “plan B” climber. However, not all of the effort was wasted – the heat exchanger design turns out to be very important in keeping their PV cells cool – more on that on the next post.

As a side note, Bert Murray and Matt Abrams have vowed that if the prize money is not awarded this year, they will solve the Helium seal issue and be back next year with a working Stirling climber.
http://www.spaceelevatorgames.org/

And there is this....

Quote
Othertypesofreceiversarepossible,suchaslaserturbojetswhichuselaser power insteadof
combustiontoheatairandproducethrust,butphotovoltaicreceiversarethe best developed.
http://www.scribd.com/doc/37446434/Laser-Power-for-UAVs


--------------------------------------------------------------------

Quote
In a gaming sense, how does a geo-stationary nuclear powered sattellite which produces a laser transimitted to the surface to a collector

I can only say this:
Quote
The idea of harnessing lasers to deliver power to a receiving solar cell has slowly gained traction over the years. A U.S. company called Solaren signed an agreement with California-based Pacific Gas & Electric to supply space-based solar power by 2016.

Japan also plans to launch its own solar power satellite by 2015, as a precursor to a larger model that would provide power to 300,000 homes. Europe's biggest aerospace company, EADS Astrium, would put its own solar-collecting demo satellite into orbit by the end of the decade. Such projects have also drawn plenty of skepticism.
http://www.popsci.com/technology/article/2010-04/skeeter-zapping-laser-entrepreneur-turns-sights-space-solar-power


Quote
I know power output would be an awful amount to produce a beam to reach the surface
Actually - not reely. If you'r point is to just send a laser (by a means of few photons) then all you need is a few kW laser that can go from Earth to the moon and back. On Mars, with it's thin air, it "should" be even easier.

But for transfering power from Mars orbit to Mars surface the situation is even better than on Earth.
Why?
1) Thin air.
2) GEO Mars orbit is 17,200 km (10,625 miles)
and Earth's GEO orbit is at: 35,700 km (22,183 miles)
so the laser "dot" would be smaller on the surface, and thus - be stronger.


Quote
Anyways, giving astronauts portable (or not) lasers to power equipment sounds like to much of a temptation to start firing at rivial factions... before you know it there will be Mars wars.
:D

Poland here. My time: GMT + 1h
Writing a book about Mars. Any ideas? Type to me.
I'am an Astrobiology/Biology student.

profit004

  • MCCS Test
  • Mission Commander
  • ******
  • Posts: 418
Re: Wireless energy transfer - Idea
« Reply #8 on: March 16, 2011, 02:22:27 PM »
1 watt lasers burn nice holes in things, these are much more diffuse than I expected, but that is because it uses a really heavy defocusing array.

I would like to know how much the truck mounted beam spreading and defocusing array weighs now that I see they are not using raw laser light anymore but a very diffuse beam.

As for the cooling system, the spreading of the beam simplify's things greatly for larger power loads, however, I would like to know if an acetone system would really work on mars. 

Still most important factor now is how much does that truck mounted beam spreading  and tracking weigh.




Marco2001

  • Mission Commander
  • *****
  • Posts: 353
Re: Wireless energy transfer - Idea
« Reply #9 on: March 16, 2011, 03:59:23 PM »
I would like to know if an acetone system would really work on mars.
 

Cooling equipement in Martian environment (Temperature, Preasure and Temperature shift) is mostly similar to those used in satelites on the vacuum of space. Satelites use the same fluid-evaporating techniqe. Small changes in fluid's mass and composition can make it more efficient.

Quote
Two Phase Heat Transport Loops

In recent years capillary-pumped loops have been the center of extensive research and development at ESA.

Capillary-Pumped Loops (CPL) and Loop Heat Pipes (LHP) allow the transport of large amounts of heat over larger distances and provide also more flexibility during ground testing compared to classical heat pipes.

Such new systems are currently baselined for use in deployable radiators, thermal control of high power e.g. laser-based instruments, heat transport from remotely located equipment to radiators and in other important areas.
http://mechanical-engineering.esa.int/thermal/fluidloops.html

Quote
Heat Pipes - An Introduction

Heat pipes are highly efficient heat transfer devices based on a continuous evaporation/condensation cycle of a suitable working fluid inside a hermetically sealed container - They have found widespread application on nearly all space missions.

The level of powerful electronic systems being integrated into modern communications and scientific research satellites is still increasing, and the improved processing power and electronics speed gives rise to the generation of more unwanted heat which needs to be dissipated by radiator panels into deep space.

Todays' telecom spacecraft use large numbers of heat pipe devices to transport heat from dissipating equipment to radiators and to spread this heat within the radiators.

Heat pipes can also be built in rather small sizes for integration into electronic units or for the cooling of small/mini satellites.
http://mechanical-engineering.esa.int/thermal/heatpipes.html

More info about cooling technologies in space-programs:
Spacecraft Thermal Control Handbook - http://www.aero.org/publications/gilmore/gilmore-1.html
Spacecraft Thermal Control [PDF presentation] - http://www.ieec.fcr.es/english/formacio/cva/apunts/P._Planas/Presentation.pdf
Spacecraft Thermal Control Website [ESA] - http://mechanical-engineering.esa.int/thermal/

-------------------------------------------------------

Still most important factor now is how much does that truck mounted beam spreading  and tracking weigh.
 

Quote
We're thrilled to announce that Laser tool manufacturer TRUMPF has stepped forward with a lucrative offer to support teams with its state-of-the-art laser equipment.

Being a world leader in disc laser technology, TRUMPF took a natural interest in the power beaming games, and is providing both hardware and expertise to enable the 1-km climb. TRUMPF is contributing a top-of-the-line TruDisk 8002 high power laser for use at the 2008-9 games, as well as on-site operation and engineering support for participating teams.

Dilas supplied the two Laser Diode power sources in the 2007 games, and is offering this year an integrated light source designed specifically for power beaming application to the 1 km range.

 You can see different lasers on those sites:
http://www.trumpf-laser.com/
http://www.dilas.com/

I'am not an expert so I just picked the first bank laser.

Quote
Vertical Stacks
Conduction-Cooled QCW, Uncollimated
100-150W per bar, 6-20 bars
 

Conduction-cooled QCW stacks with very low pitch (400µm) are produced for applications in the defense market. Peak powers can be reached up to 300W per bar at 2% duty cycle.  Fast-axis collimated versions are available with 1.6mm pitch.


Quote
The TruDisk laser is a diode-pumped commercial laser source used for industry laser processes such as cutting and welding. It offers exceptional beam quality at high power which easily enables the 1-km range, as well as an innovative fiber-optics based beam distribution system that allows multiple teams to use the same beam source.

For power beaming applications, the beam is expanded over a large area so that its intensity is reduced by several orders of magnitude. The beam is then directed at a photovoltaic panel similar to solar panels used on rooftops as a clean electrical energy source.
http://www.spaceelevatorblog.com/?p=905


Poland here. My time: GMT + 1h
Writing a book about Mars. Any ideas? Type to me.
I'am an Astrobiology/Biology student.

Utini

  • Specialist
  • ***
  • Posts: 23
Re: Wireless energy transfer - Idea
« Reply #10 on: March 21, 2011, 08:38:10 PM »
The cooling loop information was pulled directly from NASA and ESA sources re: the ISS PV cooling loop; this is for 110 kW of power. As I'm sure you're aware, acetone as a cooling agent, is limited to moderately low power transfers due to the flare point of acetone. It will also have a much lower boiling point on Mars unless some method of maintaining pressure is taken.  For these reasons, ammonia is most commonly used on space-borne cooling loops.  Ammonia has a lower specific heat capability than acetone, and thus more is required to cool the receiver.

Regarding the space power system, power sats, as discussed in previous threads, would beam diffuse microwave "spotlights" onto an array of wires and diodes that would convert the microwaves into AC current.  The biggest drawbacks for this would be the erection and maintainance of a rather sizeable array for power collection and efficiency losses as a colony moves away from the equator, primarily due to elongation of the footprint.

While this power beaming might be feasible, if less than practical, for general housekeeping, many extra uses, especially of smelting, would require impractical to insane amounts of electrical storage. Aluminum, especially requires tens of MWs for moderately extended lengths of time (15+ minutes) as part of the smelting process.  Other ores require less power, but similar orders of magnitude.

Mecanico

  • Specialist
  • ***
  • Posts: 44
Re: Wireless energy transfer - Idea
« Reply #11 on: March 26, 2011, 05:29:33 PM »
Marco, I think that there is better way for wireless (almost) electric energy transfer. It is called Tesla Transformer, well known as Tesla Coil. It has only one "bug" - there is no way to power up a plane, becouse both transmitter and receivers needs to be grounded.
RESISTANCE IS FUTILE
Earth TZ: UT+1 (CEST)

Marco2001

  • Mission Commander
  • *****
  • Posts: 353
Re: Wireless energy transfer - Idea
« Reply #12 on: March 27, 2011, 01:27:46 PM »
Why is it better?

Poland here. My time: GMT + 1h
Writing a book about Mars. Any ideas? Type to me.
I'am an Astrobiology/Biology student.

Mecanico

  • Specialist
  • ***
  • Posts: 44
Re: Wireless energy transfer - Idea
« Reply #13 on: March 27, 2011, 03:43:33 PM »
Because You don't need any highly sophisticated devices for tracking devices, high power lasers, specialized receivers (PV cells?). Transmitter is just a Tesla Coil, for receiving energy you need antenna (piece of non-insulated wire), transformer, and another one piece of wire for contact with ground. Simple and (almost) unbreakable. What can go wrong with it? If someone will set primary winding incorrectly (not in harmonics) there is possibility to burn secondary winding' insulation.
RESISTANCE IS FUTILE
Earth TZ: UT+1 (CEST)